NEC Computer Monitor V221W User Manual

V191W  
V221W  
User’s Manual  
 
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT  
USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS  
THE PRONGS CAN BE FULLY INSERTED.  
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
CAUTION  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM  
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE  
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER  
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause  
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.  
This symbol alerts the user that important literature concerning the operation and maintenance of this unit  
has been included. Therefore, it should be read carefully in order to avoid any problems.  
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not  
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the  
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.  
European  
Continental  
Plug Type  
North America  
U.K.  
Chinese  
Japanese  
Plug Shape  
Country  
Voltage  
U.S.A./Canada  
120*  
EU (except U.K.)  
230  
U.K.  
230  
China  
220  
Japan  
100  
*When operating the V191W/V221W monitor with its AC 125-240V power supply, use a power supply cord that matches the  
power supply voltage of the AC power outlet being used.  
NOTE:  
This product can only be serviced in the country where it was purchased.  
Registration Information  
Declaration  
Declaration of the Manufacturer  
We hereby certify that the colour monitors  
V191W (TFT185W80PS)/V221W (TFT22W90PS)  
are in compliance with:  
and marked with  
Council Directive 2006/95/EC:  
– EN 60950-1  
Council Directive 2004/108/EC:  
– EN 55022  
NEC Display Solutions, Ltd.  
4-13-23, Shibaura,  
Minato-Ku  
Tokyo 108-0023, Japan  
– EN 61000-3-2  
– EN 61000-3-3  
– EN 55024  
English-1  
 
Canadian Department of Communications Compliance Statement  
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.  
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.  
FCC Information  
1.  
Use the attached specified cables with the V191W/V221W color monitor so as not to interfere with radio and television  
reception.  
(1)  
The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,  
and meet the following condition.  
Power supply cord  
Plug shape  
Non shield type, 3-conductor  
U.S.A  
(2)  
Please use the supplied shielded video signal cable, 15-pin mini D-SUB to D-SUB cable or DVI-D to DVI-D cable.  
Use of other cables and adapters may cause interference with radio and television reception.  
2.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult your dealer or an experienced radio/TV technician for help.  
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.  
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify  
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,  
Washington, D.C., 20402, Stock No. 004-000-00345-4.  
Declaration of Conformity  
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
U.S. Responsible Party: NEC Display Solutions of America, Inc.  
Address:  
500 Park Blvd, Suite 1100  
Itasca, Illinois 60143  
(630) 467-3000  
Tel. No.:  
Type of Product:  
Display Monitor  
Equipment Classification: Class B Peripheral  
Models: V191W (TFT185W80PS)  
V221W (TFT22W90PS)  
We hereby declare that the equipment specified above conforms  
to the technical standards as specified in the FCC Rules.  
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.  
ENERGY STAR is a U.S. registered trademark.  
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,  
Norway, Spain, Sweden, U.K.  
All other brands and product names are trademarks or registered trademarks of their respective owners.  
®
As an ENERGY STAR Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STAR  
guidelines for energy efficiency. The ENERGY STAR emblem does not represent EPA endorsement of any product or service.  
English-2  
 
Contents  
Your new NEC LCD monitor box* should contain the following:  
LCD monitor with tilt base  
Power Cord  
Video Signal Cable  
Setup Manual  
CD-ROM (only EU)  
Base Stand  
Stand Neck  
Setup  
Manual  
CD-ROM  
(only EU)  
Setup Manual  
Power Cord  
Video Signal Cable  
LCD monitor  
(Stand not connected)  
(Type of power cord included will  
depend on the where the LCD  
monitor is to be shipped)  
*
Remember to save your original box and packing material to transport or ship the monitor.  
Quick Start  
To attach the Neck/Base to the LCD monitor.  
1. Insert the front of the Stand neck into the holes in the front of Base stand.  
The snapping tabs on the Base stand should fit into the hole on the Stand neck  
(Figure S.1).  
2. Insert the front of the Stand neck into the holes in the LCD monitor.  
The snapping tabs on the LCD monitor should fit into the hole on the Stand neck  
(Figure S.1).  
To attach the LCD monitor to your system, follow these instructions:  
1. Turn off the power to your computer.  
LCD monitor  
2. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable  
connected with the monitor to the connector of the display card in your system  
(Figure A.1). Tighten all screws.  
Stand neck  
Base stand  
For the Mac: Connect the Macintosh cable adapter (not included) to the computer.  
Attach the 15-pin mini D-SUB signal cable to the Macintosh cable adapter  
(Figure A.2). Tighten all screws.  
NOTE:  
Some Macintosh systems do not require a Macintosh cable adapter.  
Figure S.1  
Macintosh Cable Adapter  
(not included)  
Figure A.1  
Figure A.2  
English-3  
 
3. Connect one end of the power cord to the monitor and the other end to the power outlet (Figure B.1).  
NOTE:  
NOTE:  
Please confirm that the tabs are completely secure.  
Please refer to Caution section of this manual for proper selection of power cord.  
4. Turn on the monitor with the front power button and the computer (Figure C.1).  
18˚ Tilt  
Power Cord  
D-Sub  
Power Button  
Figure B.1  
Figure C.1  
5. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.  
For further adjustments, use the following OSD controls:  
• Image Setup  
• Image Position  
Refer to the Controls section of this User’s Manual for a full description of these OSD  
controls.  
NOTE:  
If you have any problem, please refer to the Troubleshooting section of this  
User’s Manual.  
Tilt  
Grasp both sides of the monitor screen with your hands and adjust the tilt as desired  
(Figure TS.1).  
Remove Monitor Stand for Mounting  
To prepare the monitor for alternative mounting purposes:  
Figure TS.1  
1. Disconnect all cables.  
2. Place monitor face down on a non-abrasive surface (Figure R.1).  
3. Insert the thin rod into the hole in the back of LCD monitor and using your thumbs, press the tabs on the back side of base  
stand in the direction of the arrows the pull out the stand as indicated (Figure R.1)  
4. Connect the AC cord to the back of the monitor (Figure R.2).  
5. Reverse this process to re-attach stand.  
NOTE:  
NOTE:  
Use only VESA-compatible alternative mounting method.  
Handle with care when removing monitor stand.  
Tabs  
Non-abrasive surface  
Figure R.1  
Figure R.2  
English-4  
 
Removing the Base  
NOTE:  
Always remove the Base when shipping the LCD.  
1. Place monitor face down on a non-abrasive surface (Figure R.1).  
2. Insert the thin rod into the hole in the back of LCD monitor and using your thumbs, press the tabs on the back side of base  
stand in the direction of the arrows the pull out the stand as indicated (Figure R.1).  
Connecting a Flexible Arm  
This LCD monitor is designed for use with a flexible arm.  
Please use the screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor must be  
mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor.  
The LCD monitor shall only be used with an approved arm (e.g. GS mark).  
4 x 12 mm with lock washer and flat washer  
12 mm  
Thickness of Bracket  
(Arm) 2.0 ~ 3.2 mm  
M4  
100 mm  
Tighten all screws  
100 mm  
Specifications  
4-SCREWS (M4)  
(MAX depth: 8.5 mm)  
Weight of LCD assembly: 3.0 kg (MAX) - (V191W)  
4.1 kg (MAX) - (V221W)  
English-5  
 
Controls  
OSD (On-Screen Display) control buttons on the front of the monitor function  
as follows:  
1. Basic function at pressing each key  
Button  
At No OSD  
showing  
Shortcut to Bright adjust  
window.  
Shortcut to Contrast adjust  
window.  
“Auto adjust” operate.  
Reset operation.  
Showing OSD.  
At OSD showing  
(Icon selection stage)  
Go to Adjustment stage.  
Cursor goes to left.  
Cursor goes to right.  
At OSD showing Go to Icon selection stage.  
(Adjustment stage)  
Adjust value decrease or  
Cursor for adjust goes to left. Cursor for adjust goes to  
right.  
Adjust value increase or  
2. OSD structure  
Main Menu (Icon Select)  
Main Menu (Adjust)  
Press  
“MENU”  
key  
Press  
“MENU”  
key  
Press “MENU” key  
Adjust by using  
“–” or “+”  
Example Tool:  
Press “MENU” key  
Press  
“MENU” key  
Press  
“–” or “+”  
Press  
“–” or “+”  
Press  
“MENU” key  
Sub Menu (Icon Select)  
Adjust by using  
“–” or “+”  
Sub Menu (Adjust)  
English-6  
 
BRIGHTNESS  
Adjusts the overall image and background screen brightness.  
To enter the ECO MODE, press the “AUTO” button.  
CONTRAST  
Adjusts the image brightness in relation to the background.  
AUTO CONTRAST  
Adjusts the image displayed for non-standard video inputs.  
AUTO ADJUST  
Automatically adjusts the Image Position, the H. Size and Fine setting.  
LEFT/RIGHT  
Controls Horizontal Image Position within the display area of the LCD.  
DOWN/UP  
Controls Vertical Image Position within the display area of the LCD.  
H. SIZE  
Adjusts the horizontal size by increasing or decreasing this setting.  
FINE  
Improves focus, clarity and image stability by increasing or decreasing this setting.  
COLOUR CONTROL SYSTEMS  
Five colour presets (9300/7500/sRGB/USER/NATIVE) select the desired colour setting.  
COLOUR RED  
Increase or decreases Red. The change will appear on screen.  
COLOUR GREEN  
Increase or decreases Green. The change will appear on screen.  
COLOUR BLUE  
Increase or decreases Blue. The change will appear on screen.  
TOOL  
Selecting TOOL allows you to get into the sub menu.  
FACTORY PRESET  
Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings.  
Individual settings can be reset by highlighting the control to be reset and pressing the “+” button.  
EXIT  
Selecting EXIT allows you exit OSD menu/ sub menu.  
LANGUAGE  
OSD control menus are available in nine languages.  
OSD TURN OFF  
The OSD control menu will stay on as long as it is in use. In the OSD Turn OFF submenu, you can select how  
long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are  
10 - 120 seconds by 5 seconds step.  
English-7  
 
OSD LOCK OUT  
This control completely locks out access to all OSD control functions without Brightness and Contrast. When  
attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are  
locked out. To activate the OSD Lock Out function, press “AUTO”, then “+” key and hold down simultaneously.  
To de-activate the OSD Lock Out, press “AUTO”, then “+” key and hold down simultaneously.  
RESOLUTION NOTIFIER  
If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not at  
optimal resolution.  
EXPANSION  
Selects the zoom mode.  
FULL: The image is expanded to full screen, regardless of the resolution.  
ASPECT: The image is expanded without changing the aspect ratio.  
DDC/CI  
Turns ON or OFF the two way communication and control of the monitor.  
MONITOR INFO  
Indicates the model and serial numbers of your monitor.  
CARBON SAVING  
Show saving value of Carbon foot print.  
Carbon meter value is updated each 5 min.  
INPUT RESOLUTION  
V191W  
Select resolution’s priority of input signal to one of the following signal: 1280x768, 1360x768, 1366x768.  
V221W  
Select resolution’s priority of input signal to one of the following signal: 1280x768, 1360x768 and 1366x768 or  
1400x1050 and 1680x1050.  
1280x768, 1360x768, 1366x768: Determines the resolution to 1280x768, 1360x768 or 1366x768.  
1400x1050, 1680x1050: Determines the resolution to 1400x1050 or 1680x1050.  
OSD Warning  
OSD Warning menus disappear with MENU button.  
NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is  
a change of input signal or video is inactive, the No Signal window will appear.  
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After the power  
is turned on or there is a change of input signal or the video signal doesn’t have proper timing, the Out Of Range  
menu will appear.  
English-8  
 
Recommended use  
Safety Precautions and Maintenance  
FOR OPTIMUM PERFORMANCE, PLEASE NOTE  
THE FOLLOWING WHEN SETTING UP AND  
USING THE LCD COLOUR MONITOR:  
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose  
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.  
Do not spill any liquids into the cabinet or use your monitor near water.  
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful  
or fatal or may cause electric shock, fire or equipment failure.  
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.  
Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to  
the monitor.  
The power supply cord you use must have been approved by and comply with the safety standards of your country.  
(Type H05VV-F 3G 0.75mm2 should be used in Europe).  
In U.K, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.  
Do not place any objects onto the monitor and do not use the monitor outdoors.  
The lamps in this product contain mercury. Please dispose according to state, local or federal law.  
Do not bend, crimp or otherwise damage the power cord.  
Do not use monitor in high temperatured, humid, dusty, or oily areas.  
Do not cover vent on monitor.  
Do not touch LCD panel surface while transporting, mounting and setting. Applying pressure on the LCD panel can cause  
serious damage.  
To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks, make sure to install  
the monitor in a stable location and take measures to prevent falling.  
Immediately turn off the power, unplug your monitor from the wall outlet and move to a safe location then refer servicing to  
qualified service personnel under the following conditions. If the monitor is used in this condition, the monitor may cause fall,  
fire and electric shock:  
If the monitor stand has been cracked or peeled.  
If the monitor has been wobbled.  
If the monitor has an unusual odor.  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into the monitor.  
If the monitor has been exposed to rain or water.  
If the monitor has been dropped or the cabinet damaged.  
If the monitor does not operate normally by following operating instructions.  
If glass is broken, handle with care.  
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.  
Allow adequate ventilation around the monitor so that heat can properly dissipate.  
Do not block ventilated openings or place the monitor near a radiator or other heat  
sources. Do not put anything on top of monitor.  
CAUTION  
The power cable connector is the primary means of detaching the system from the  
power supply. The monitor should be installed close to a power outlet which is easily  
accessible.  
Handle with care when transporting. Save packaging for transporting.  
Carry the monitor holding the built-in handle and bottom frames of the monitor.  
Do not carry holding only the stand.  
Image Persistence: Please be aware that LCD Technology may experience a phenomenon known as Image Persistence.  
Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike  
CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period  
of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was  
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be  
turned off for one hour to erase the image.  
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and  
using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.  
English-9  
 
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN  
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE  
FOLLOWING WHEN YOU POSITION THE MONITOR:  
For optimum performance, allow 20 minutes for warm-up.  
Adjust the monitor height so that the top of the screen is at or slightly below eye level.  
Your eyes should look slightly downward when viewing the middle of the screen.  
Position your monitor no closer than 40 cm and no further away than 70 cm from your  
eyes. The optimal distance is 50 cm.  
Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.  
Position the monitor at a 90° angle to windows and other light sources to minimize  
glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your  
screen.  
If reflected light makes it hard for you to see your screen, use an anti-glare filter.  
Adjust the monitor’s brightness and contrast controls to enhance readability.  
Use a document holder placed close to the screen.  
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize  
turning your head while you are typing.  
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).  
Get regular eye checkups.  
Ergonomics  
To realize the maximum ergonomics benefits, we recommend the following:  
Adjust the Brightness until the background raster disappears.  
Do not position the Contrast control to its maximum setting.  
Use the preset Size and Position controls with standard signals.  
Use the preset Colour Setting.  
Use non-interlaced signals with a vertical refresh rate between 60-75 Hz.  
Do not use primary colour blue on a dark background, as it is difficult to see and may produce eye fatigue to insufficient  
contrast.  
Cleaning the LCD Panel  
When the liquid crystal panel is stained with dust or dirt, please wipe with soft cloth gently.  
Please do not rub the LCD panel with hard material.  
Please do not apply pressure to the LCD surface.  
Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface.  
Cleaning the Cabinet  
Unplug the power supply  
Gently wipe the cabinet with a soft cloth  
To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.  
NOTE:  
Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,  
alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or  
vinyl to the cabinet for a long time. These types of fluids and fabrics can cause the paint to deteriorate, crack or  
peel.  
English-10  
 
Specifications - V191W  
Monitor Specifications  
V191W Monitor  
Notes  
LCD Module  
Diagonal: 47.01 cm/18.5 inches  
Active matrix; thin film transistor (TFT)  
liquid crystal display (LCD);  
0.30 (H) mm x 0.30 (V) mm dot pitch;  
280 cd/m2 (typ) white luminance, 1000:1  
contrast ratio (typ), response time: 5 ms.  
Viewable Image Size: 47.01 cm/18.5 inches  
Native Resolution (Pixel Count): 1366 x 768  
Input Signal  
Video: ANALOG 0.7 Vp-p/75 Ohms  
Sync: Separate sync.TTL Level (Positive/Negative)  
Display Colours  
Analog input: 16,7 M  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 81.0 kHz  
Vertical: 55 Hz to 76 Hz  
Automatically  
Automatically  
Viewing Angle  
Left/Right: -85°/+85° (CR>10)  
Up/Down: -75°/+85° (CR>10)  
Resolutions  
Supported  
Analog output: 640 x 400*1 @ 70 Hz  
720 x 400*1 @ 70 Hz  
Some systems may not support all  
modes listed.  
640 x 480*1 @ 60 Hz to 75 Hz  
800 x 600*1 @ 56 Hz to 75 Hz  
832 x 624*1 @ 75 Hz  
1024 x 768*1 @ 60 Hz to 75 Hz  
1152 x 864*1 @ 70 Hz to 75 Hz  
1280 x 960*1 @ 60 Hz  
1280 x 1024*1 @ 60 Hz  
1360 x 768*1 @ 60 Hz  
Recommended resolution is 60 Hz for  
1366 x 768*1 @ 60 Hz.................................optimal display performance.  
Active Display Area  
Horizontal: 409.8 mm  
Vertical: 230.4 mm  
Power Supply  
Current Rating  
Dimensions  
100 - 240 V ~ 50/60 Hz  
0.75 - 0.4 A/100 - 240V  
Landscape: 445.4 mm (W) x 338.2 mm (H) x 193.8 mm (D) (with stand)  
445.4 mm (W) x 270.1 mm (H) x 63.5 mm (D) (without stand)  
Weight  
3.2 kg  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 30% to 80%  
Altitude: 0 to 6562 Feet/0 to 2000 m  
Storage Temperature: -10°C to +60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40000 Feet/0 to 12192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is  
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on  
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-11  
 
Specifications - V221W  
Monitor Specifications  
V221W Monitor  
Notes  
LCD Module  
Diagonal: 54.79 cm/21.6 inches  
Active matrix; thin film transistor (TFT)  
liquid crystal display (LCD);  
0.248 (H) mm x 0.248 (V) mm dot pitch;  
300 cd/m2 (typ) white luminance, 800:1  
contrast ratio (typ), response time: 5 ms.  
Viewable Image Size: 54.79 cm/21.6 inches  
Native Resolution (Pixel Count): 1920 x 1080  
Input Signal  
Video: ANALOG 0.7 Vp-p/75 Ohms  
Sync: Separate sync.TTL Level (Positive/Negative)  
Display Colours  
Analog input: 16,7 M  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 81.0 kHz  
Vertical: 55 Hz to 76 Hz  
Automatically  
Automatically  
Viewing Angle  
Left/Right: -85°/+85° (CR>10)  
Up/Down: -80°/+80° (CR>10)  
Resolutions  
Supported  
Analog and 720 x 400*1 @ 70 Hz  
digital output: 640 x 480*1 @ 60 Hz to 75 Hz  
800 x 600*1 @ 56 Hz to 75 Hz  
832 x 624*1 @ 75 Hz  
Some systems may not support all  
modes listed.  
1024 x 768*1 @ 60 Hz to 75 Hz  
1152 x 864*1 @ 70 Hz to 75 Hz  
1280 x 960*1 @ 60 Hz to 75 Hz  
1280 x 1024*1 @ 60 Hz to 75 Hz  
1360 x 786*1 @ 60 Hz  
1366 x 786*1 @ 60 Hz  
1440 x 900*1 @ 60 Hz  
1400 x 1050*1 @ 60 Hz  
1600 x 1200*1 @ 60 Hz  
Recommended resolution is 60 Hz for  
1680 x 1050*1 @ 60 Hz...............................optimal display performance.  
1920 x 1080*1 @ 60 Hz  
Horizontal: 477.5 mm  
Vertical: 268.6 mm  
100 - 240 V ~ 50/60 Hz  
1.2 - 0.6 A/100 - 240V  
Active Display Area  
Power Supply  
Current Rating  
Dimensions  
Landscape: 514.5 mm (W) x 372.5 mm (H) x 193.6 mm (D) (with stand)  
514.5 mm (W) x 310.2 mm (H) x 68.5 mm (D) (without stand)  
Weight  
4.3 kg  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 30% to 80%  
Altitude: 0 to 6562 Feet/0 to 2000 m  
Storage Temperature: -10°C to +60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40000 Feet/0 to 12192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is  
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on  
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-12  
 
Features  
Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight  
limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another.  
No-touch Auto Adjust: No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup.  
Plug and Play: The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the  
monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically  
optimizing display performance.  
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a  
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions  
and lowering the air conditioning costs of the workplace.  
Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the  
resolution required.  
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.  
VESA Standard Mounting Interface: Allows users to connect their monitor to any VESA standard third party mounting arm  
or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device.  
English-13  
 
Troubleshooting  
No picture  
The signal cable should be completely connected to the display card/computer.  
The display card should be completely seated in its slot.  
Check front power Switch and computer power switch should be in the ON position.  
Check to make sure that a supported mode has been selected on the display card or system being used. (Please  
consult display card or system manual to change graphics mode.)  
Check the monitor and your display card with respect to compatibility and recommended settings.  
Check the signal cable connector for bent or pushed-in pins.  
Check the signal input.  
Power Button does not respond  
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.  
Image persistence  
Image persistence is when a “ghost” of an image remains on the screen even after the monitor has been turned off.  
Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a  
long period of time should be avoided.  
To alleviate image persistence, turn the monitor off for as long as an image was displayed. For example, if an image  
was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase  
the image.  
NOTE:  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a screen saver at regular  
intervals whenever the screen is idle or turning off the monitor when not in use.  
Image is unstable, unfocused or swimming is apparent  
Signal cable should be completely attached to the computer.  
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total. When the  
display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.  
Check the monitor and your display card with respect to compatibility and recommended signal timings.  
If your text is garbled, change the video mode to non-interlace and use 60 Hz refresh rate.  
LED on monitor is not lit (no green or amber colour can be seen)  
Power Switch should be in the ON position and power cord should be connected.  
Display image is not sized properly  
Use the OSD Image Adjust controls to increase or decrease the H.SIZE.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
No Video  
If no video is present on the screen, turn the Power button off and on again.  
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).  
English-14  
 
TCO’03  
Congratulations!  
The display you have just purchased carries the TCO’03 Displays  
label. This means that your display is designed, manufactured and  
tested according to some of the strictest quality and environmental  
requirements in the world. This makes for a high performance  
product, designed with the user in focus that also minimizes the  
impact on our natural environment.  
Some of the features of the TCO’03 Display requirements:  
Ergonomics  
• Good visual ergonomics and image quality in order to improve the working environment for  
the user and to reduce sight and strain problems. Important parameters are luminance,  
contrast, resolution, reflectance, colour rendition and image stability.  
Energy  
• Energy-saving mode after a certain time – beneficial both for the user and the environment  
• Electrical safety  
Emissions  
• Electromagnetic fields  
• Noise emissions  
Ecology  
• The product must be prepared for recycling and the manufacturer must have a certified  
environmental management system such as EMAS or ISO 14 001.  
• Restrictions on:  
- chlorinated and brominated flame retardants and polymers  
- heavy metals such as cadmium, mercury and lead.  
The requirements included in this label have been developed by TCO Development in co-  
operation with scientists, experts, users as well as manufacturers all over the world. Since the  
end of the 1980s TCO has been involved in influencing the development of IT equipment in a  
more user-friendly direction. Our labelling system started with displays in 1992 and is now  
requested by users and IT-manufacturers all over the world.  
For more information, please visit  
English-15  
 
Manufacturer’s Recycling and Energy Information  
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s  
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-  
friendly products, and always strive to help define and comply with the latest independent standards from agencies such as  
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).  
Disposing of your old NEC product  
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of  
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely  
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling  
procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end  
of its life.  
All required information concerning the disposal of the product and country-specific information on recycling facilities can be  
found on our following websites:  
Energy Saving  
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)  
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.  
V191W  
Mode  
Power consumption  
Approx. 21 W  
LED colour  
Blue  
Normal Operation  
Energy Saving Mode  
Off Mode  
Less than 1 W  
Amber  
Unlit  
Less than 0.5 W  
V221W  
Mode  
Power consumption  
Approx. 40 W  
LED colour  
Blue  
Normal Operation  
Energy Saving Mode  
Off Mode  
Less than 1 W  
Amber  
Unlit  
Less than 0.5 W  
WEEE Mark (European Directive 2002/96/EC)  
Within the European Union  
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic  
products carrying the mark (left) must be disposed of separately from normal household waste. This includes  
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your  
NEC display products, please follow the guidance of your local authority, or ask the shop where you  
purchased the product, or if applicable, follow any agreements made between yourself and NEC.  
The mark on electrical and electronic products only applies to the current European Union Member States.  
Outside the European Union  
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local  
authority so as to comply with the correct disposal method.  
English-16  
 

Miele Microwave Oven M 8260 2 User Manual
Miller Electric Welder XMT 400 User Manual
Multi Tech Systems Network Card MT2834MR6 User Manual
Murphy Switch WD300 Series User Manual
NCR Home Theater Screen NCR 5972 User Manual
Nortel Networks Switch 241 5101 200 User Manual
NXP Semiconductors Stereo Amplifier CGD944C User Manual
Oki Printer PAGE 8Z User Manual
Onkyo Stereo Receiver TX SR604 604E User Manual
Panasonic Answering Machine KX TG643 User Manual